Adafruit Feather RP2040

Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040
Adafruit Feather RP2040

Description

A new chip means a new Feather, and the Raspberry Pi RP2040 is no exception. When Adafruit saw this chip they thought "this chip is going to be awesome when we give it the Feather Treatment" and so they did! This Feather features the RP2040, and all niceties you know and love about Feather

Features

  • Measures 2.0" x 0.9" x 0.28" (50.8mm x 22.8mm x 7mm) without headers soldered in
  • Light as a (large?) feather - 5 grams
  • RP2040 32-bit Cortex M0+ dual core running at ~125 MHz @ 3.3V logic and power
  • 264 KB RAM
  • 8 MB SPI FLASH chip for storing files and CircuitPython/MicroPython code storage. No EEPROM
  • Tons of GPIO! 21 x GPIO pins with following capabilities:
    • Four 12 bit ADCs (one more than Pico)
    • Two I2C, Two SPI and two UART peripherals, we label one for the 'main' interface in standard Feather locations
    • 16 x PWM outputs - for servos, LEDs, etc
    • The 8 digital 'non-ADC/non-peripheral' GPIO are consecutive for maximum PIO compatibility
  • Built in 200mA+ lipoly charger with charging status indicator LED
  • Pin #13 red LED for general purpose blinking
  • RGB NeoPixel for full color indication.
  • On-board STEMMA QT connector that lets you quickly connect any Qwiic, STEMMA QT or Grove I2C devices with no soldering!
  • Both Reset button and Bootloader select button for quick restarts (no unplugging-replugging to relaunch code)
  • 3.3V Power/enable pin
  • Optional SWD debug port can be soldered in for debug access
  • 4 mounting holes
  • 12 MHz crystal for perfect timing.
  • 3.3V regulator with 500mA peak current output
  • USB Type C connector lets you access built-in ROM USB bootloader and serial port debugging

Inside the RP2040 is a 'permanent ROM' USB UF2 bootloader. What that means is when you want to program new firmware, you can hold down the BOOTSEL button while plugging it into USB (or pulling down the RUN/Reset pin to ground) and it will appear as a USB disk drive you can drag the firmware onto. Folks who have been using Adafruit products will find this very familiar - we use the technique on all our native-USB boards. Just note you don't double-click reset, instead hold down BOOTSEL during boot to enter the bootloader!

The RP2040 is a powerful chip, which has the clock speed of our M4 (SAMD51), and two cores that are equivalent to our M0 (SAMD21). Since it is an M0 chip, it does not have a floating point unit, or DSP hardware support - so if you're doing something with heavy floating-point math, it will be done in software and thus not as fast as an M4. For many other computational tasks, you'll get close-to-M4 speeds!

For peripherals, there are two I2C controllers, two SPI controllers, and two UARTs that are multiplexed across the GPIO - check the pinout for what pins can be set to which. There are 16 PWM channels, each pin has a channel it can be set to (ditto on the pinout).

You'll note there's no I2S peripheral, or SDIO, or camera, what's up with that? Well instead of having specific hardware support for serial-data-like peripherals like these, the RP2040 comes with the PIO state machine system which is a unique and powerful way to create custom hardware logic and data processing blocks that run on their own without taking up a CPU. For example, NeoPixels - often we bitbang the timing-specific protocol for these LEDs. For the RP2040, we instead use PIO object that reads in the data buffer and clocks out the right bitstream with perfect accuracy. Same with I2S audio in or out, LED matrix displays, 8-bit or SPI based TFTs, even VGA! In MicroPython and CircuitPython you can create PIO control commands to script the peripheral and load it in at runtime. There are 2 PIO peripherals with 4 state machines each.

Reviews

Add to Wish List Adafruit Feather RP2040
Product Code: ADA-4884
€ 11.53
Ex. VAT
10 or more € 10.95 Ea. (-5%)
Need larger quantities? Ask for a quote!
  • 21 piece(s) in stock
  • Ordered before 17:00, shipped today.
  • Shipping from € 8.91 to United States
  • 30 days money back guarantee
  • Fast shipping from The Netherlands

Documentation

Specifications

General
Product CodeADA-4884
BrandAdafruit
MPN4884
PlatformRaspberry Pi (RP2040)
Feather

You might like these as well

The terminal blocks allow you to connect to any of the external Feather pins, great for wiring temporary or permanent installations.
€ 14.83 Ex. VAT
Raspberry Pi Pico is the first product built on silicon designed in-house at Raspberry Pi. The board is programmable in MicroPython or C/C++.
€ 3.26 Ex. VAT
The feature packed Arduino Nano RP2040 Connect brings the new Raspberry Pi RP2040 microcontroller to the Nano form factor.
€ 24.75 Ex. VAT
The feature packed Arduino Nano RP2040 Connect with Headers brings the new Raspberry Pi RP2040 microcontroller to the Nano form factor.
€ 26.41 Ex. VAT
A Pirate-brand RP2040-powered microcontroller
€ 14.01 Ex. VAT
Fast shipping
Order before 17:00h (Mon-Fri) for same day shipping.
Money back guarantee
You have a 30-day return period on your order
Worldwide shipping
Shipped from the Netherlands using PostNL and DHL.