HiFiBerry Digi+ Transformer met Spacers

HiFiBerry Digi+ Transformer met Spacers
5 - 2 beoordeling(en).
Artikelcode: RPI-HB+DIGITR

€ 35,95 Excl. BTW: € 29,71
25 op voorraad voor directe levering.
Vandaag voor 17:00 uur besteld, morgen in huis.

Aantal: In winkelwagen

Hoeveelheid Per stuk
10+€ 35,05 (Excl. BTW: € 28,97)
50+€ 34,16 (Excl. BTW: € 28,23)
  • Gratis verzending vanaf € 50 binnen Nederland en België
  • Verzending via PostNL & UPS
  • Snelle levering uit eigen NL magazijn

The HiFiBerry Digi+ is a high-quality S/PDIF output board for the Raspberry Pi. It is designed as an add-on board that connects to the main header of the Raspberry Pi


  • Dedicated S/PDIF interface chip supports up to 192kHz/24bit resolution
  • Optical (Toslink) and electrical outputs
  • Bit-perfect output, audio data stream will not be modified in any way
  • Connects directly to the Raspberry Pi, no additional cables needed
  • No soldering. The Digi+ comes as a pre-fabricated kit. You just plug it onto the Raspberry Pi. The board conform to the Raspberry Pi hardware-attached-on-top (HAT) specification.
  • Directly powered from the Raspberry Pi, no additional power supply
  • High-bandwidth output transformer provides full galvanic isolation of the electrical output
  • Integrated EEPROM for automatic configuration (with write-protection).
    Note that this feature is still in development by the Raspberry Pi foundation. You will be able to upgrade your HiFiBerry DAC+ when it is officially available. The sound card already works without this feature.
  • Comes with all components required to mount it. We include 4 M2.5x12mm spacers to fix the board onto the Raspberry Pi.


  • Pre-soldered HifiBerry Digi+ with output transformer
  • Nylon spacer set

Compatible with

  • Raspberry Pi Model A+
  • Raspberry Pi Model B+
  • Raspberry Pi 2 Model B
  • Raspberry Pi 3 Model B

Important note: While the hardware is able to output DTS/Dolby Digital, software has to be adapted to support this. We will support the developers to implement this. Unfortunately we can’t guarantee that this feature will work with a specific software. Please ask the developers of the software if this is supported.

Output Transformer

The output transformer provides a full galvanic isolation between the Raspberry Pi and your DAC on the electrical output. Usual consumer-grade SPDIF outputs do not use output transformers. Usually this works without problems. However, many audio enthusiast like to use this option. If you’re not sure, the standard version is most likely ok for you.
The output transformer does not have any effect on the optical output. Therefore if you plan to use only the optical output, the standard version will do the job.

Merk: HiFiBerry
4 ( 4 / 5 )
Zelfde verhaal als hier boven,
Even je config.txt veranderen en dan kun je de optische uitgang in kodi selecteren.
Dts, 5.1 etc. Werkt allemaal prima.
5 ( 5 / 5 )
Zonet op mijn RPI2 geplaatst en in het doorzichtige kastje gebouwd (DIGI+ en kastje hier gekocht). Daarna wel even in /boot/config.txt de regel: 'dtoverlay=hifiberry-digi' (zie ook: toegevoegd en hij werd gelijk herkend (regel in dmesg is: snd-hifiberry-digi sound: wm8804-spdif <-> 3f203000.i2s mapping ok) in JRiver MediaCenter20 for ARM (zie Aangesloten op de MyDAC via COAX en luisteren maar.
Kortom werkt prima. Nu bepalen of er verschil is tussen geluid via USB2 of COAX.


Je naam:

Je beoordeling: Note: HTML-code wordt niet vertaald!

Oordeel: Slecht           Goed

Voer onderstaande code in: